| Напряжение питания и ток | 12 to 30V dc (10% max. ripple); 50 mA max. @ 24V dc (exclusive of load) |
|---|---|
| Зона чувствительности |
LG5:45 to 60 mm LG10:75 to 125 mm |
| Источник света | 670 nm visible red IEC and CDRH Class 2 laser; 0.20 mW max. radiant output power |
| Цепи защиты | Protected against reverse polarity and transient over voltages |
| Конфигурация Выхода | One discrete output and one analog output
Discrete (switched) and alarm outputs: SPST solid-state switch:NPN (current sinking) or PNP (current sourcing), depending on model Analog output:0 to 10V dc or 10 to 0V dc (voltage sourcing) or 4 to 20 mA or 20 to 4 mA (current sourcing), depending on model |
| Выходная мощность |
Discrete (switched) and alarm output:100 mA max. OFF-state leakage current:less than 5 µA Output saturation: NPN:less than 1.2V @ 10 mA; less than 1.6V @ 100 mA
PNP:less than 1.2 mV @ 10 mA; less than 600 mV @ 100 mA
Analog voltage output:2.5 k ohms min. load impedanceAnalog current output:1 k ohms max. @ 24V; max. load resistance = [Vcc-4.5/0.02 ohms] |
| Выходная цепь защиты | Discrete and alarm outputs are protected against continuous overload and short circuit. |
| Выходной время отклика |
Discrete outputs: Fast:2 milliseconds ON/OFF
Medium:10 milliseconds ON/OFF
Slow:100 milliseconds ON/OFF
Analog output (-3 dB):Fast:450 Hz (1 millisecond average/1 millisecond update rate)
Medium:45 Hz (10 milliseconds average/2 millieconds update rate)
Slow:4.5 Hz (100 milliseconds average/5 millisecond update rate)
|
| Задержка при включении питания | 1.25 second |
| Color Sensitivity |
LG5:less than 75 µm for white to dark gray ceramic target LG10:less than 100 µm for white to dark gray ceramic target |
| Analog Linearity | Specified @ 24V dc, 22 ° C, using a white ceramic test surface (see Application Notes)
LG5:± 60 µm over 45 to 60 mm sensing window; ±10 µm over 49 to 51 mm sensing window LG10:±200 µm over 75 to 125 mm sensing window; ±20 µm over 95 to 100 mm sensing window |
| Analog Resolution and Repeatability of Discrete Trip Point | Specified @ 24V dc, 22 ° C, using a white ceramic test surface (see Application Notes)
LG5: Fast:less than 40 µm @ 50 mm
Medium:less than 12 µm @ 50 mm
Slow:less than 3 µm @ 50 mm
LG10:Fast:less than 150 µm @ 100 mm
Medium:less than 50 µm @ 100 mm
Slow:less than 10 µm @ 100 mm
|
| Discrete Output Hysteresis |
LG5:less than 0.2 mm LG10:less than 1.0 mm |
| Температурный Эффект |
LG5:± 7 µm/° C LG10:±25 µm/° C |
| Минимальный размер окна |
LG5:1.5 mm LG10:5 mm |
| Remote TEACH and Laser Control Input Impedance | 18 k ohms (65 k ohms min. @ 5V dc) |
| Дистанционное обучение |
To TEACH:connect yellow wire to +5 to 30V dc To disable:connect yellow wire to 0 to +2V dc (or open connection) |
| регулировка |
Response speed:Push button toggles between fast, medium and slow (see Выходной время отклика ) Window limits (analog or discrete):TEACH-mode programming of near and far window limits. Limits may also be taught remotely. Analog output slope:The first limit taught is assigned to minimum output current or voltage (4 mA or 0V dc) |
| Laser Control | Connect green wire to +5 to 30V dc to enable laser beam; connect to 0 to +2V dc (or open connection) to disable; 250 millisecond delay upon enable/disable |
| индикатор |
Green Power ON LED:indicates when power is ON, overloaded output and laser status Yellow Output LED:indicates when discrete load output is conducting Red Signal LED:indicates target is within sensing range and the condition of the received light signal Tri-color Red/Green/Yellow TEACH LED:indicates sensor is ready for programming each limit Red:analog
Green:discrete
Yellow:simultaneous analog and discrete
Yellow Fast/Slow LEDs:combination of 2 lights ON/OFF indicates 1 of 3 response speeds |
| конструкция |
Housing:Zinc alloy die-cast, plated and painted finish Cover:aluminum with painted finish Lens:acrylic |
| Степень защиты | IP67; NEMA 6 |
| соединение | 7-conductor (with drain) 2 m or 9 m shielded PVC-jacketed attached cable, or 150 mm pigtail with 8-pin Euro-style quick-disconnect fitting. QD cables are ordered separately. |
| Условия эксплуатации |
Temperature:-10° to +50° C Relative humidity:90% @ 50° C (non-condensing) |
| Вибрации и удары |
Vibration:60 Hz, 30 minutes, 3 axes Shock:30G for 11 milliseconds, half-sine wave, 3 axes |
| Рекомендации по применению | For comparison, a white ceramic test surface has approximately 91% of the reflectivity of a white Kodak test card with a matte finish. A dark gray ceramic test surface has approximately 11% of the reflectivity of a white Kodak test card with a matte finish. (Allow 15-minute warm-up for maximum linearity.) |
- Conserves production space by using a one-piece design
- Does not touch parts it measures, so can be used with moving processes, hot parts and sticky parts
- Provides 12 to 30V dc supply voltage with either an NPN or PNP discrete output, and a 4-20 mA or 0-10V dc analog output
- Automatically scales the analog output over the width of the programmed sensing window
- Features outstanding maximum resolution of 3 µm for flat white targets
- Uses an ultra-narrow beam to precisely measure distance, height or thickness
- Available in ranges of 45 to 60 mm (LG5) and 75 to 125 mm (LG10)
- Lets you pick the exact range you need with the push of a button
- Features push-button TEACH-mode programming for custom sensing windows
- Offers remote programming for added security and convenience
- Uses push-button programming for three output response speeds