At a glance
| Pressure resistant up to 500 bar |
| Expected service life of up to 1 million pressure cycles |
| Sensing range of 3 mm flush |
| IP 68 |
| Stainless steel housing with active surface made from stable high-performance ceramic |
| State-of-the-art ASIC technology from SICK |
| Gas-tight at the sensor face |
Your benefits
| Reduced maintenance costs |
| Extremely resilient and durable |
| Up to 50 times longer service life compared to conventional sensors under pressure cycles |
| Simple compensation of cylinder tolerances |
| Simple integration due to small design |
| Controlled piston deceleration |
| Increased piston service life due to collision prevention at the end of the work cycle |
| Features | |||
| Housing: | Cylindrical | ||
| Thread size: | M14 x 1.5 | ||
| Sensing range Sn: | 3 mm | ||
| Assured sensing range Sa: | 2.4 mm | ||
| Pressure resistance: | ≤ 500 bar | ||
| Installation type: | Flush | ||
| Частота переключений: | 500 Hz | ||
| Output type: | NPN | ||
| Output function: | NC | ||
| Electrical wiring: | DC 3-wire | ||
| Enclosure rating: | IP 68 1) | ||
| Тип подключения: | Connector M12, 4-pin | ||
| Механика/электроника | |||
| Supply voltage: | 10 V DC ... 30 V DC | ||
| Vacuum resistance: | 10-8Torr 1) | ||
| Пульсации: | ≤ 20 % 2) | ||
| Падение напряжения: | ≤ 2 V 3) | ||
| Потребляемая мощность: | ≤ 10 mA 4) | ||
| Time delay before availability: | ≤ 50 ms | ||
| Hysteresis: | 1 % ... 15 % 5) | ||
| Повторяемость: | ≤ 4 % 6)7) | ||
| Температурный дрейфт: | 15 % | ||
| EMC: | According to EN 60947-5-2 8) | ||
| Непрерывный ток Ia: | ≤ 200 mA | ||
| защита от короткого замыкания: |  |
||
| Защита от обратной полярности: | |
||
| Импульсная защита: | - | ||
| Ударная и вибрационная устойчивость: | 30 g, 11 ms / 10 ... 55 Hz, 1 mm | ||
| Ambient operating temperature: | -25 °C ... +80 °C | ||
| Материал корпуса: | Stainless steel, V4A | ||
| Материал корпуса крышки: | Ceramics, ZrO2 | ||
| Size sealing ring: | 11.5 mm x 2.0 mm | ||
| Material sealing ring: | NBR | ||
| Длина корпуса: | 65 mm | ||
| Thread length: | 11 mm | ||
| Момент затяжки, Макс.: | ≤ 70 Nm | ||
| Понижающие коэффициенты | |||
| Примечание: | The values are reference values which may vary | ||
| Carbon steel St37 (Fe): | 1 | ||
| Stainless steel (V2A, 304): | Ca. 0.85 | ||
| Copper (Cu): | Ca. 0 | ||
| Aluminum (Al): | Ca. 0 | ||
| Brass (Br): | Ca. 0.15 | ||
| Installation note | |||
| Remark: | Associated graphic see "Installation" | ||
At a glance
| Pressure resistant up to 500 bar |
| Expected service life of up to 1 million pressure cycles |
| Sensing range of 3 mm flush |
| IP 68 |
| Stainless steel housing with active surface made from stable high-performance ceramic |
| State-of-the-art ASIC technology from SICK |
| Gas-tight at the sensor face |
Your benefits
| Reduced maintenance costs |
| Extremely resilient and durable |
| Up to 50 times longer service life compared to conventional sensors under pressure cycles |
| Simple compensation of cylinder tolerances |
| Simple integration due to small design |
| Controlled piston deceleration |
| Increased piston service life due to collision prevention at the end of the work cycle |
| Features | |||
| Housing: | Cylindrical | ||
| Thread size: | M14 x 1.5 | ||
| Sensing range Sn: | 3 mm | ||
| Assured sensing range Sa: | 2.4 mm | ||
| Pressure resistance: | ≤ 500 bar | ||
| Installation type: | Flush | ||
| Частота переключений: | 500 Hz | ||
| Output type: | NPN | ||
| Output function: | NO | ||
| Electrical wiring: | DC 3-wire | ||
| Enclosure rating: | IP 68 1) | ||
| Тип подключения: | Connector M12, 4-pin | ||
| Механика/электроника | |||
| Supply voltage: | 10 V DC ... 30 V DC | ||
| Vacuum resistance: | 10-8Torr 1) | ||
| Пульсации: | ≤ 20 % 2) | ||
| Падение напряжения: | ≤ 2 V 3) | ||
| Потребляемая мощность: | ≤ 10 mA 4) | ||
| Time delay before availability: | ≤ 50 ms | ||
| Hysteresis: | 1 % ... 15 % 5) | ||
| Повторяемость: | ≤ 4 % 6)7) | ||
| Температурный дрейфт: | 15 % | ||
| EMC: | According to EN 60947-5-2 8) | ||
| Непрерывный ток Ia: | ≤ 200 mA | ||
| защита от короткого замыкания: | |
||
| Защита от обратной полярности: | |
||
| Импульсная защита: | - | ||
| Ударная и вибрационная устойчивость: | 30 g, 11 ms / 10 ... 55 Hz, 1 mm | ||
| Ambient operating temperature: | -25 °C ... +80 °C | ||
| Материал корпуса: | Stainless steel, V4A | ||
| Материал корпуса крышки: | Ceramics, ZrO2 | ||
| Size sealing ring: | 11.5 mm x 2.0 mm | ||
| Material sealing ring: | NBR | ||
| Длина корпуса: | 65 mm | ||
| Thread length: | 11 mm | ||
| Момент затяжки, Макс.: | ≤ 70 Nm | ||
| Понижающие коэффициенты | |||
| Примечание: | The values are reference values which may vary | ||
| Carbon steel St37 (Fe): | 1 | ||
| Stainless steel (V2A, 304): | Ca. 0.85 | ||
| Copper (Cu): | Ca. 0 | ||
| Aluminum (Al): | Ca. 0 | ||
| Brass (Br): | Ca. 0.15 | ||
| Installation note | |||
| Remark: | Associated graphic see "Installation" | ||
At a glance
| Pressure resistant up to 500 bar |
| Expected service life of up to 1 million pressure cycles |
| Sensing range of 3 mm flush |
| IP 68 |
| Stainless steel housing with active surface made from stable high-performance ceramic |
| State-of-the-art ASIC technology from SICK |
| Gas-tight at the sensor face |
Your benefits
| Reduced maintenance costs |
| Extremely resilient and durable |
| Up to 50 times longer service life compared to conventional sensors under pressure cycles |
| Simple compensation of cylinder tolerances |
| Simple integration due to small design |
| Controlled piston deceleration |
| Increased piston service life due to collision prevention at the end of the work cycle |
| Features | |||
| Housing: | Cylindrical | ||
| Thread size: | M14 x 1.5 | ||
| Sensing range Sn: | 3 mm | ||
| Assured sensing range Sa: | 2.4 mm | ||
| Pressure resistance: | ≤ 500 bar | ||
| Installation type: | Flush | ||
| Частота переключений: | 500 Hz | ||
| Output type: | PNP | ||
| Output function: | NC | ||
| Electrical wiring: | DC 3-wire | ||
| Enclosure rating: | IP 68 1) | ||
| Тип подключения: | Connector M12, 4-pin | ||
| Механика/электроника | |||
| Supply voltage: | 10 V DC ... 30 V DC | ||
| Vacuum resistance: | 10-8Torr 1) | ||
| Пульсации: | ≤ 20 % 2) | ||
| Падение напряжения: | ≤ 2 V 3) | ||
| Потребляемая мощность: | ≤ 10 mA 4) | ||
| Time delay before availability: | ≤ 50 ms | ||
| Hysteresis: | 1 % ... 15 % 5) | ||
| Повторяемость: | ≤ 4 % 6)7) | ||
| Температурный дрейфт: | 15 % | ||
| EMC: | According to EN 60947-5-2 8) | ||
| Непрерывный ток Ia: | ≤ 200 mA | ||
| защита от короткого замыкания: | |
||
| Защита от обратной полярности: | |
||
| Импульсная защита: | - | ||
| Ударная и вибрационная устойчивость: | 30 g, 11 ms / 10 ... 55 Hz, 1 mm | ||
| Ambient operating temperature: | -25 °C ... +80 °C | ||
| Материал корпуса: | Stainless steel, V4A | ||
| Материал корпуса крышки: | Ceramics, ZrO2 | ||
| Size sealing ring: | 11.5 mm x 2.0 mm | ||
| Material sealing ring: | NBR | ||
| Длина корпуса: | 65 mm | ||
| Thread length: | 11 mm | ||
| Момент затяжки, Макс.: | ≤ 70 Nm | ||
| Понижающие коэффициенты | |||
| Примечание: | The values are reference values which may vary | ||
| Carbon steel St37 (Fe): | 1 | ||
| Stainless steel (V2A, 304): | Ca. 0.85 | ||
| Copper (Cu): | Ca. 0 | ||
| Aluminum (Al): | Ca. 0 | ||
| Brass (Br): | Ca. 0.15 | ||
| Installation note | |||
| Remark: | Associated graphic see "Installation" | ||
At a glance
| Pressure resistant up to 500 bar |
| Expected service life of up to 1 million pressure cycles |
| Sensing range of 3 mm flush |
| IP 68 |
| Stainless steel housing with active surface made from stable high-performance ceramic |
| State-of-the-art ASIC technology from SICK |
| Gas-tight at the sensor face |
Your benefits
| Reduced maintenance costs |
| Extremely resilient and durable |
| Up to 50 times longer service life compared to conventional sensors under pressure cycles |
| Simple compensation of cylinder tolerances |
| Simple integration due to small design |
| Controlled piston deceleration |
| Increased piston service life due to collision prevention at the end of the work cycle |
| Features | |||
| Housing: | Cylindrical | ||
| Thread size: | M14 x 1.5 | ||
| Sensing range Sn: | 3 mm | ||
| Assured sensing range Sa: | 2.4 mm | ||
| Pressure resistance: | ≤ 500 bar | ||
| Installation type: | Flush | ||
| Частота переключений: | 500 Hz | ||
| Output type: | PNP | ||
| Output function: | NO | ||
| Electrical wiring: | DC 3-wire | ||
| Enclosure rating: | IP 68 1) | ||
| Тип подключения: | Connector M12, 4-pin | ||
| Механика/электроника | |||
| Supply voltage: | 10 V DC ... 30 V DC | ||
| Vacuum resistance: | 10-8Torr 1) | ||
| Пульсации: | ≤ 20 % 2) | ||
| Падение напряжения: | ≤ 2 V 3) | ||
| Потребляемая мощность: | ≤ 10 mA 4) | ||
| Time delay before availability: | ≤ 50 ms | ||
| Hysteresis: | 1 % ... 15 % 5) | ||
| Повторяемость: | ≤ 4 % 6)7) | ||
| Температурный дрейфт: | 15 % | ||
| EMC: | According to EN 60947-5-2 8) | ||
| Непрерывный ток Ia: | ≤ 200 mA | ||
| защита от короткого замыкания: | |
||
| Защита от обратной полярности: | |
||
| Импульсная защита: | - | ||
| Ударная и вибрационная устойчивость: | 30 g, 11 ms / 10 ... 55 Hz, 1 mm | ||
| Ambient operating temperature: | -25 °C ... +80 °C | ||
| Материал корпуса: | Stainless steel, V4A | ||
| Материал корпуса крышки: | Ceramics, ZrO2 | ||
| Size sealing ring: | 11.5 mm x 2.0 mm | ||
| Material sealing ring: | NBR | ||
| Длина корпуса: | 65 mm | ||
| Thread length: | 11 mm | ||
| Момент затяжки, Макс.: | ≤ 70 Nm | ||
| Понижающие коэффициенты | |||
| Примечание: | The values are reference values which may vary | ||
| Carbon steel St37 (Fe): | 1 | ||
| Stainless steel (V2A, 304): | Ca. 0.85 | ||
| Copper (Cu): | Ca. 0 | ||
| Aluminum (Al): | Ca. 0 | ||
| Brass (Br): | Ca. 0.15 | ||
| Installation note | |||
| Remark: | Associated graphic see "Installation" | ||