At a glance
| Speed and acceleration monitoring |
| Monitoring range: 6 to 12,000 pulses/min. and 0.1 to 2 pulses/sec.² |
| Switching and pulse output |
| Intelligent start-up delay |
| Speed monitoring can be flexibly configured via two thresholds |
| Flexible sensor settings, monitoring, extended diagnostics, and visualization thanks to IO-Link |
| Sensing range: 7 mm flush |
| Type M18 |
Your benefits
| Speed-independent detection of speed changes |
| Faster detection of speed changes than conventional speed monitors |
| No readjustment after speed changes necessary |
| Precise and convenient configuration via software |
| IO-Link provides easy data access from the PLC |
| No time-consuming, individual configuration of start-up delay feature necessary |
| Reliable output signal thanks to adjustable speed thresholds (hysteresis) |
| No expensive counter cards necessary in PLC |
| Features | |||
| Housing: | Cylindrical | ||
| Thread size: | M18 x 1 | ||
| Sensing range Sn: | 7 mm | ||
| Assured sensing range Sa: | 5.6 mm | ||
| Installation type: | Flush | ||
| Output type: | PNP | ||
| Output function: | NO | ||
| Electrical wiring: | DC 4-wire | ||
| Enclosure rating: | IP 67 1) | ||
| Тип подключения: | Connector M12, 4-pin | ||
| Output Q Imp: | Pulse output (The pulse sequence corresponds to the damping frequency) | ||
| Output Q: | Output type (dependant on the adjusted threshold) | ||
| Speed range, adjustable via two thresholds: | 6...12,000 impulses / min 2) | ||
| Acceleration range, adjustable: | 0.1...2 impulses / sec² 3) | ||
| Time delay, adjustable: | Mode 0: No start-up delay Mode 1: 0...254 sec., adjustable Mode 2: When reaching the upper threshold |
||
| Механика/электроника | |||
| Supply voltage: | 10 V DC ... 30 V DC | ||
| Пульсации: | ≤ 10 % | ||
| Падение напряжения: | ≤ 2.5 V 1) | ||
| Потребляемая мощность: | ≤ 35 mA 2) | ||
| Hysteresis: | 5 % ... 15 % 3) | ||
| Повторяемость: | ≤ 2 % 4)5) | ||
| Температурный дрейфт: | ± 10 % | ||
| EMC: | According to EN 60947-5-2 | ||
| Непрерывный ток Ia: | ≤ 100 mA | ||
| Wire-break protection: | 0 | ||
| защита от короткого замыкания: |  |
||
| Защита от обратной полярности: | |
||
| Импульсная защита: | |
||
| Ударная и вибрационная устойчивость: | 30 g, 11 ms/10 Hz ... 55 Hz, 1 mm | ||
| Ambient operating temperature: | -25 °C ... +75 °C | ||
| Материал корпуса: | Metal, Nickel-plated brass | ||
| Материал корпуса крышки: | Plastic, PA6 | ||
| Длина корпуса: | 69 mm | ||
| Thread length: | 52 mm | ||
| Момент затяжки, Макс.: | ≤ 40 Nm | ||
| Status indicator QImp: | LED, yellow | ||
| Status indicator Q: | LED, blau | ||
| Minimum response time: | Mode acceleration monitoring 1 sec, Mode speed monitoring 50 ms | ||
| Factory setting: | Operating mode: acceleration monitoring, Threshold acceleration: 1 pulse/sec², Start-up delay mode: time delay, Upper/lower threshold speed: 200/300 pulses/min, Time delay: 5 sec | ||
| Fieldbus integration: | IO-Link V1.0 | ||
| Mode: | COM 2 (38k4) | ||
| Cycle time: | 5 ms | ||
| Process data length: | 16 Bit | ||
| Process data structure: | 1 bit pulse output, 1 bit switching output, 14 bit measured value | ||
| Понижающие коэффициенты | |||
| Примечание: | The values are reference values which may vary | ||
| Carbon steel St37 (Fe): | 1 | ||
| Stainless steel (V2A, 304): | 0.8 | ||
| Copper (Cu): | 0.4 | ||
| Aluminum (Al): | 0.45 | ||
| Brass (Br): | 0.4 | ||
| Installation note | |||
| B: | 18 mm | ||
| C: | 18 mm | ||
| D: | 18 mm | ||
| F: | 56 mm | ||
| Remark: | Associated graphic see "Installation" | ||
At a glance
| Speed and acceleration monitoring |
| Monitoring range: 6 to 1,200 pulses/min. and 0.1 to 2 pulses/sec.² |
| Switching and pulse output |
| Intelligent start-up delay |
| Speed monitoring can be flexibly configured via two thresholds |
| Flexible sensor settings, monitoring, extended diagnostics, and visualization thanks to IO-Link |
| Types M18 and M30 |
| Sensing range up to 10 mm flush |
Your benefits
| Speed-independent detection of speed changes |
| Faster detection of speed changes than conventional speed monitors |
| No readjustment after speed changes necessary |
| Precise and convenient configuration via software |
| IO-Link provides easy data access from the PLC |
| No time-consuming, individual configuration of start-up delay feature necessary |
| Reliable output signal thanks to adjustable speed thresholds (hysteresis) |
| No expensive counter cards necessary in PLC |
| Features | |||
| Housing: | Cylindrical | ||
| Thread size: | M18 x 1 | ||
| Sensing range Sn: | 7 mm | ||
| Assured sensing range Sa: | 5.6 mm | ||
| Installation type: | Flush | ||
| Output type: | PNP | ||
| Output function: | NO | ||
| Electrical wiring: | DC 4-wire | ||
| Enclosure rating: | IP 67 1) | ||
| Тип подключения: | Connector M12, 4-pin | ||
| Output Q Imp: | Pulse output (The pulse sequence corresponds to the damping frequency) | ||
| Output Q: | Output type (dependant on the adjusted threshold) | ||
| Speed range, adjustable via two thresholds: | 6...1,200 impulses / min 2) | ||
| Acceleration range, adjustable: | 0.1...2 impulses / sec² 3) | ||
| Time delay, adjustable: | Mode 0: No start-up delay Mode 1: 0...254 sec., adjustable Mode 2: When reaching the upper threshold |
||
| Механика/электроника | |||
| Supply voltage: | 10 V DC ... 30 V DC | ||
| Пульсации: | ≤ 10 % | ||
| Падение напряжения: | ≤ 2 V 1) | ||
| Потребляемая мощность: | ≤ 10 mA 2) | ||
| Hysteresis: | 5 % ... 15 % 3) | ||
| Повторяемость: | ≤ 2 % 4)5) | ||
| Температурный дрейфт: | ± 10 % | ||
| EMC: | According to EN 60947-5-2 | ||
| Непрерывный ток Ia: | ≤ 100 mA | ||
| Wire-break protection: | 0 | ||
| защита от короткого замыкания: | |
||
| Защита от обратной полярности: | |
||
| Импульсная защита: | |
||
| Ударная и вибрационная устойчивость: | 30 g, 11 ms/10 Hz ... 55 Hz, 1 mm | ||
| Ambient operating temperature: | -25 °C ... +75 °C | ||
| Материал корпуса: | Metal, Nickel-plated brass | ||
| Материал корпуса крышки: | Plastic, PA6 | ||
| Длина корпуса: | 69 mm | ||
| Thread length: | 52 mm | ||
| Момент затяжки, Макс.: | ≤ 40 Nm | ||
| Status indicator QImp: | LED, green | ||
| Status indicator Q: | LED, yellow | ||
| Fieldbus integration: | IO-Link V1.0 | ||
| Mode: | COM 2 (38k4) | ||
| Cycle time: | 2.3 ms | ||
| Process data length: | 16 Bit | ||
| Process data structure: | 1 bit pulse output, 1 bit switching output, 14 bit measured value | ||
| Понижающие коэффициенты | |||
| Примечание: | The values are reference values which may vary | ||
| Carbon steel St37 (Fe): | 1 | ||
| Stainless steel (V2A, 304): | 0.8 | ||
| Copper (Cu): | 0.4 | ||
| Aluminum (Al): | 0.45 | ||
| Brass (Br): | 0.4 | ||
| Installation note | |||
| Remark: | Associated graphic see "Installation" | ||